Factory Free sample 3d Laser Scanning Australia - Print material-exquisite white-8006 – Digital Manufacturing
Factory Free sample 3d Laser Scanning Australia - Print material-exquisite white-8006 – Digital Manufacturing Detail:
3D Printing Materials
Exquisite white-8006
Introduction of 3D Printing Materials
Characteristics
SZUV-W8006
PRODUCT DESCRIPTION
SZUV-W8006 is an ABS like SL resin which has accurate and durable features. It is designed for solid state SLA platforms. SZUV-W8006 can be applied in master patterns, concept models, general parts and functional prototypes in the field of automotive, medical and consumer electronics industries.The parts duability building with SZUV-W8006 is over 6.5months.SZUV-W8006
TYPICAL FEATURES
-Liquid resin`s medium viscosity, so easy recoating, easy clean parts and machines
-Improved strength retained, improved dimensions retention of parts in humid condition
-need minimal part finishing
-Long shelf life in machine
TYPICAL BENEFITS
-Need less part finishing time,easier post-curing
-Buliding accurate and high tough parts with an improved dimensional stability
-High quality controls for vacuum casting parts
-Low shrink and good resistance to yellowing
-Magnificent white color
-Outstanding machinable SLA material
Physical Properties – Liquid Material
Appearance | White |
Density | 1.13g/cm3 @ 25 ℃ |
Viscosity | 376 cps @ 27 ℃ |
Dp | 0.148 mm |
Ec | 7.8 mJ/cm2 |
Building layer thickness | 0.1mm |
Mechanical Properties of Post-Cured Material
MEASUREMENT | TEST METHOD | VALUE |
90-minute UV post-cure | ||
Hardness, Shore D | ASTM D 2240 | 87 |
Flexural modulus, Mpa | ASTM D 790 | 2,592-2,675 |
Flexural strength, Mpa | ASTM D 790 | 70- 75 |
Tensile modulus, MPa | ASTM D 638 | 2,599-2,735 |
Tensile strength, MPa | ASTM D 638 | 39-56 |
Elongation at break | ASTM D 638 | 13 -20% |
Poisson`s Ratio | ASTM D 638 | 0.4-0.43 |
Impact strength notched Izod, J/m | ASTM D 256 | 35 - 45 |
Heat deflection temperature, ℃ | ASTM D 648 @66PSI | 62 |
Glass transition,Tg,℃ | DMA,E”peak | 73 |
Coefficient of thermal expension, /℃ | TMA(T<Tg) | 95*E-6 |
Density, g/cm3 | 1.16 | |
Dielectric Constant 60 Hz | ASTM D 150-98 | 4.6 |
Dielectric Constant 1 kHz | ASTM D 150-98 | 3.9 |
Dielectric Constant 1 MHz | ASTM D 150-98 | 3.6 |
Dielectric StrengthkV/mm | ASTM D 1549-97a | 14.9 |
Note: the temperature of szuv-w8006 should not be too high. Please use it below 25c.Recommended temperature for use and preservation is 18-25 ℃
Fire Fighting Measures
(1) extinguishant
Dry powder fire extinguishing agent, alcohol resistant foam extinguishing agent, carbon dioxide, dry sand, spray water.
(2) Special risk
Fires may produce irritation and harmful gas
(3) The firemen of protective measures
Fireman should wear protective appliances (eye protection, protective clothing, mailing gas with gas mask, etc.), put out the fire in the windward.
6. Accidental Release Measures
(1) Homework personnel protective equipment
Ensure adequate ventilation, wear suitable protective clothing, make a good job in hand and eye/face protection.
(2) Environmental protection measures
Prevent products from entering the drain or open water
(3) Cleaning method
For a small amount of leakage, use dry sand, soil and towels absorb the residual liquid, recycling and airtight container.
For a large number of leakage, leakage of liquid can be in front of the embankment, the introduction of recycle to safe place.
(4) Secondary hazard prevention measures
Quickly remove all fire spark (ban on smoking in nearby, and the ignition).
7. Handling And Storage
(1) Operation treatment technical measures
Avoid contact with eyes, skin and clothing. Don’t inhaling mist or steam, don’t accidentally swallow, keep container tightly closed after the thorough cleaning.
(2) Partial or full ventilation Maintain adequate ventilation
(3) Safe handling matters needing attention No smoke, no fire
(4) Safe storage conditions
Stored in a cool, well ventilated place, away from heat, sparks and flames. Keep container tightly closed until it is put into use.
(5) packaging container and material
In the process of custody, please do not transfer to other containers. Don’t fall back to the original containers of products that will be used.
Cases
SOME OF MY PROJECTS
Education
Rapid prototype
Auto Parts
Constructional design
Art Design
Medical
Product detail pictures:
Related Product Guide:
Comparing Polarityte (PTE) & Materialise (MTLS) | Most Expensive 3d Printer
ForeScout Technologies Inc. (FSCT) and Materialise NV (NASDAQ:MTLS) Comparison side by side | Handheld 3d Scanner Review
The really abundant projects administration experiences and just one to one particular provider model make the substantial importance of organization communication and our easy understanding of your expectations for Factory Free sample 3d Laser Scanning Australia - Print material-exquisite white-8006 – Digital Manufacturing , The product will supply to all over the world, such as: Nigeria, Argentina, Turin, We follow up the career and aspiration of our elder generation, and we're eager to open up a new prospect in this field, We insist on "Integrity, Profession, Win-win Cooperation", because we have now a strong backup, that are excellent partners with advanced manufacturing lines, abundant technical strength, standard inspection system and good production capacity.
By Cora from Malta - 2015.10.09 19:07
The factory technical staff not only have high level of technology, their English level is also very good, this is a great help to technology communication.
By Ingrid from Ukraine - 2016.09.16 13:44